-
If you enjoy the forum please consider supporting it by signing up for a NES Membership The benefits pay for the membership many times over.
-
Be sure to enter the NES/Pioneer Valley Arms February Giveaway ***Smith & Wesson SD9VE 9MM***
NFA SBR engraving in Mass
- Thread starter Da_lucche
- Start date
http://www.a10armsandammo.com
http://www.nitorlaser.com/Firearms.aspx
These guys are in Southwick. Not sure of their prices. My form is pending so I'll stop in and talk to them pretty soon.
http://www.nitorlaser.com/Firearms.aspx
These guys are in Southwick. Not sure of their prices. My form is pending so I'll stop in and talk to them pretty soon.
Got approved Tuesday. I had some free time today, So I called up Jacks Machine Company to see if they had availability and told me to come on down. Was in and out in a total of 5 min. Got to watch it happen and make final say on it, not just a you get what we give you.
Talked to the guy at the desk (Mike?) very friendly and told me they just received their FFL.
I will be back for my next NFA item.
- - - Updated - - -
They are great guys down there. I havent had an engraving done but I would not hesitate to use them. They are just another 30 min further from me than Jacks is.
Talked to the guy at the desk (Mike?) very friendly and told me they just received their FFL.
I will be back for my next NFA item.
- - - Updated - - -
They are great guys down there. I havent had an engraving done but I would not hesitate to use them. They are just another 30 min further from me than Jacks is.
I can vouch for Nitor Laser and Engraving. I had my SBR engraved there and their prices and work quality are excellent. It is veteran owned and very knowledgeable.
Just called Harry at GNW this morning. Apparently he doesn't want anything to do with firearms anymore.
Any other places near Metro-west that will do this, preferably on a weekend?
boilermaker
NES Member
I went down to Jack's a couple weeks ago to get 3 lowers done. I had called the previous day to see if they had time, and went down the next day. In and out and very nice to deal with.
Are they only open Monday through Friday? I'm hoping to avoid taking time off from work.
Thanks.
boilermaker
NES Member
I took the morning off from work as i was coming from west of Worcester. I didn't ask about weekends at the time and having been there, it seems unlikely. They are a job shop, their equipment can run for extended periods of time without people, so you might be able to get in if they have some job that requires folks to come in on a weekend, but I doubt its norm. It was helpful knowing I had an "appointment" so-to-speak, I called to confirm before heading out too and they were ready when I arrived so it was in and out for me.
Thanks. I called and am going down there Monday. I have the day off, but they are working.
For you guys that got it done at Jack's, do I need to remove my stock and tube? Hoping I can at least leave the tube in place. Planning in getting it done on the side of the magwell.
boilermaker
NES Member
I had stripped lowers engraved on the magwell. The guy taking care of me was real nice, he looked like he was twenty but had been working there for a number of years and had started there when he was 16 as a side / summer gig. But I digress, he was just able to lay the lower in the machine, no clamps, just supports so they probably have something that can support the tube to make it work. You are able to see the layout superimposed directly on the lower before the laser does its thing. I was surprised at how small the font size could be. Good luck with your job.
Just had my engraving done at Jacks Machine Company. Excellent service as others said, they know what size/depth is required. Got to chat with the machinist (Bill) while it was done. Highly recommend.
Old post, but I'm 33, haha. Been here 17 years.
We haven't seen many people in for engraving in a while, but for whatever reason the past few weeks I've had like 10 people in for SBR and serial number engraving. Weird.
Parker Duofold
NES Member
Just had two NFA engravings done by Bill at Jack's. Nice work and finished while I waited.:emoji_cool::emoji_grey_exclamation:
